High-Quality A1 DTF Printer with EPSON i3200-A1 (Featuring 4 Print Heads)

TODOjet UV ink is formulated to produce vibrant colors using Cyan, Magenta, Yellow, Black, White, and Varnish.
Combined, this UV inkjet ink enables companies to achieve full-color graphics and images on a wide variety of flat and cylindrical objects.

TODOjet UV ink can be used in practically any UV printers.

Adheres to a wide variety of rigid substrates including glass, plastic, and metal

CMYK + W + V available

How to use UV transfer sticker
1. Remove the transfer sticker and tear it off
2. Align the position and paste it
3. Remove the transparent film after pressing the pattern
4. Paste completed

When it is found that the pattern printed by the UV flatbed printer has left and right, and the upper and lower deviations are not aligned, it means that the x and y direction is misaligned, and the printing needs to be suspended immediately. Because the structural design and components of the x and y axis are different, the causes of fault and corresponding solutions are also different.

1. keep the machine clean:keep the important parts of the machine clean, can not be stained with oil and dust, keep the hot transfer film clean, can not be stained with fingerprints and dust, keep the bearing products clean, no dust, oil, keep the hands clean, no oil, no sweat.
2.hot stamping pressure:hot stamping pressure must be adjusted to the most appropriate, otherwise too big and easy to hurt the glue head and be hot material, too small and affect the hot stamping effect.The pressure shall be locked after adjusting to the best stamping pressure to avoid change in mass production.
3. hot temperatureIt is easy to damage the bearing material, too low hot temperature may not be able to reach the normal transfer printing.Hot temperature should be determined by the bearing material, flower film, heat transfer machine, these factors, different materials have different hot temperature.
4.hot stamping speed:hot stamping time (speed) should be determined according to the specific hot stamping, in the case of ensuring the hot stamping effect, the faster the speed, the higher the production efficiency, but some products due to some special conditions must use slow speed

1. Printed pictures have horizontal lines
2. Large color deviation
3. The edge of the picture is blurred and ink is flying
4. Printed pictures are scattered with small ink dots
5. There is ghosting in the horizontal printing
6. Printing dripping or broken ink

China’s UV printer industry has been developing for more than ten years, and it has basically reached a bottleneck in terms of flat-panel printing technology at this stage. Throughout these years, the evolution of nozzles has become a main line. Most UV printer manufacturers have started to change Epson nozzles, Seiko nozzles, Konica nozzles to Ricoh nozzles, Toshiba nozzles, Kyocera nozzles, and starlight nozzles. It is also based on the replacement of nozzles in Japan. The core point of the market is the cost-effectiveness of the print head, that is a better balance between speed, accuracy, life, and price.

Recently, heat transfer is widely used in garment printing.And in the market,we always see hot peel film and cold peel fim,even now also with warm peel film,but which one is best? Here we can do a analyze from different aspects

UV printing is environmental friendly while producing the crisp image on the printed paper boxes and gift paper boxes. Below are the benefits of the UV printing and inks.Faster turnaround time: UV inks dry instantly on the press when exposed to the UV light.Zero VOC release: unlike the conventional inks containing the chemical solvents, the UV inks release no volatile organic compounds, which is abbreviated to VOC. Extra protection of the printing because of the better resistance to smudge and abrasion.Crisp look to the printed text and graphics on the paper box and bag.

Pre-sale: With senior industry experience, analyze customer needs and future development, and customize the overall solution of recommended products and machines

With the TODOjet powder machine,you can set up different temperatures,the front heating, top heating and back heating. This will prevent the film from oil or moisture.

DTF-T30 A3 DTF Printer Features

Advanced Printheads: Equipped with 2 or 3 Epson I1600-A1 printheads for precise and high-speed printing.
Vivid Color Output: Dual CMYK + White ink configuration ensures vibrant, full-color prints with crisp, high-opacity white details for multi-material transfers.
Fast Printing Speed:
6 PASS: 12m²/h
8 PASS: 8m²/h
Ideal for both fast production runs and high-resolution detailed prints.

The heat press machine can heat various heat presses on cotton, linen, chemical fiber and other fabrics by heat transfer, and can also perform heat treatment processes such as screen printing, mucilage, foaming, etc. Landscape patterns, etc. are baked on porcelain plates and metal plates, which are especially suitable for making medals, commemorative cards, cultural shirts, etc. It is economical and practical, and the patterns are exquisite. It is replacing traditional embroidery and screen printing, and the cost and effect are much lower and better than general embroidery and multi-color screen printing.

Using the shake powder could consider these procedures.
Dusting.
1.What is the powder sprinkled with?Hot melt powder, when the heat is sticky, after the formation of glue coating;
2.Why?Stick hot melt stick to the dry ink to help eventually form the coating;
3.How to sprinkle, sprinkle how fast?Can adjust the knob on the shake powder machine;
4.How much?The powder is about 2-3cm thick to stop sprinkling the powder.
Shaking.
1.Why shake powder?Shake off the excess powder on the ink and film adhesion, so that the powder is thin and evenly attached to the ink.
2.Shake powder speed.Depending on the situation, the knob on the condition machine, about 2-3 gear ok.
Drying.

1.Why drying?Melt the hot melt powder to create a reprint pattern coating;.
2.How long will it bake?Undefinite, depending on the specific situation, mainly to ensure that the pattern feels no powder, hot melt powder all melted into coating.
3.Temperature? 90-130 ° C is ok.

Accuracy: Variable Droplet High Quality Printing
Variable Droplets for Beautifully Smooth Gradients: Features a variable droplet feature that prints ink into 3 different sizes of droplets at once

There are three main misunderstandings in the speed of UV flatbed printers: theoretical speed, speed in different modes, and actual production speed. What needs to be understood is that the speed in most sales man mouths only refers to the theoretical speed. A few professionals will mention the speed in different modes, but these are not the actual production speeds. The gap in the middle is at least Times to calculate.

1. Significant Saving on printing cost.
2. Environmentally protective, no waste ink.
3. Smooth ink flow for better printing quality.

The reasons for the white color registration and color registration problems of uv flatbed printers are: the print head is not vertical, the print head is in a bad state, the height is wrong, the two-way is not adjusted properly, and the software data parameter is set. The manifested features are pattern leakage, image shift and dislocation.

1. Machine stand
2. Front/rear two-stage heating
3. Plug-in Dalian supply
4. White Ink Stirrer
5. Nozzle area
6. Body

Compatible with popular RIP software and designed for compact efficiency, the DTF-T652/653/654 represents the pinnacle of printing technology for businesses seeking enhanced capabilities. Upgrade your printing infrastructure today and embrace the future of printing excellence.

DTF PET film with different size for your reference, 30cm*100m/roll and 60cm*100m/roll. This anti-static PET film for cold peel, it can feed continously during printing.Meanwhile, we can also offer other DTF printer consumbles like hot melt powder and pigment ink.

UV inks used in UV printers can be divided into hard ink and soft ink according to the hardness properties of the printing material. Rigid, non-bending, non-deforming materials such as glass, ceramic tile, metal plate, acrylic, wood, etc., use hard ink; elastic, bendable, twisting materials such as leather, soft film, soft PVC, etc., Use soft ink.

In DTF printing:

Special pigment ink is applied to PET film.
A powdered glue is then applied to the back and heat cured for immediate or storage-ready use.
This method offers versatility across non-cotton materials and avoids the complexities of pre-treatment or plate-making required in traditional methods. DTF printers are often paired with powder dryer machines to enhance the printing process.

Although UV printers can print patterns on the surface of hundreds or thousands of materials, due to the characteristics of the surface of different materials, the adhesion of UV ink, flexibility and other performance differences, it will lead to peeling, peeling, etc. on some materials. situation, which requires the use of UV coating to solve this problem.

No need to engrave waste and lamination, improve production efficiency, unlimited patterns, natural hollowing, lighter and breathable, short cycle and fast delivery, breaking through the limitations of traditional process color registration plate making, no plate making, 1 piece minimum order cost-effective, no high cost The investment in equipment and venues greatly reduces the investment cost.

Inkjet technology utilizes tiny droplets of ink to facilitate direct printing without the device coming into contact with the printing surface. Because the technology supports non-contact printing, it can be applied to a variety of media and is now being introduced into a wide range of fields from general-purpose to industrial.

Heat transfer has high requirements for the selection of ink, hot melt powder and transfer film, which is related to the quality of printing and the service life of the machine. The supporting consumables recommended by our factory are the optimal quality and the best supporting scheme.

Top cover,6 heat tubes
Master switch,Sealant strip surround
A3 film tray,Cold fan
TEMP setup and timing settings

RGB color model refers to the three primary colors of light: Red, Green, and Blue,the three primary color light with different proportions of the sum, can produce a variety of color light, in theory, red, green, blue light can be mixed out of all colors.

Pure black when printing is generally used for smaller characters. If the full-color black (C100 M100 Y100 K100) is used, the ink concentration is too high, the ink is not easy to dry and easy to print. Therefore, it is recommended to use monochrome black (C0 M0 Y0 K100).

The original 6-color ink has more stable color performance, wider color gamut, more colorful picture layers, and greatly improved preservation in terms of light resistance, oxidation resistance and corrosion resistance. Combined with Epson’s micro piezoelectric printing technology, users can enjoy true high-quality print output.