Reasons and Solutions for No Ink from Nozzle of UV Flatbed Printer

Symptoms of poor ink output from uv flatbed printers are: flying ink, dripping ink, drawing and so on. There are roughly eight kinds of reasons that cause this kind of failure. In actual application, the UV flatbed printer design varies from different manufacturers. Some may have 10 reasons, and some may have 6 reasons. But mastering the following 7 kinds can solve the problem that 99% of the nozzles have poor ink discharge.

Powder shaking machine usually together with our 60cm DTF printer, it can keep continous automatic dusting powder and curing the PET film during printing.The speed can match with 2 heads i3200 DTF printer. After curing, you can store the printed PET film for heat transfer use.These released PET films are suitable for any fabric garment printing, like T-shirt printing,chemical fiber, non-woven fabric printing,linen printing,canvas printing,leather printing,silk printing,etc.

Despite some limitations regarding adhesion to certain surfaces, crystal labels remain one of the best options for advertising customization due to their versatility, cost-effectiveness, and high-quality finish. For businesses looking to elevate their brand identity with personalized labels that make a lasting impression, AGP crystal labels offer the perfect solution. With strong adhesion, three-dimensional visual appeal, and a premium finish, crystal labels are setting the standard for innovative branding and advertising customization.

When many friends buy a UV printer, the general manufacturer will promise the machine warranty for 1 year or 2 years or 3 years, etc., but there is a saying: Ink circuit system and print heads are not covered by the warranty.

1. keep the machine clean:keep the important parts of the machine clean, can not be stained with oil and dust, keep the hot transfer film clean, can not be stained with fingerprints and dust, keep the bearing products clean, no dust, oil, keep the hands clean, no oil, no sweat.
2.hot stamping pressure:hot stamping pressure must be adjusted to the most appropriate, otherwise too big and easy to hurt the glue head and be hot material, too small and affect the hot stamping effect.The pressure shall be locked after adjusting to the best stamping pressure to avoid change in mass production.
3. hot temperatureIt is easy to damage the bearing material, too low hot temperature may not be able to reach the normal transfer printing.Hot temperature should be determined by the bearing material, flower film, heat transfer machine, these factors, different materials have different hot temperature.
4.hot stamping speed:hot stamping time (speed) should be determined according to the specific hot stamping, in the case of ensuring the hot stamping effect, the faster the speed, the higher the production efficiency, but some products due to some special conditions must use slow speed

The produced glue has the characteristics of water resistance, good fastness, fast drying speed, not easy to block the network, and does not affect the color of the ink, and is a new type of environmentally friendly material.

No limit of fabric materials
No need pre-coating
CMYK+ White (Fluoresent color for option)
2pcs EPSON i3200-A1 (4 heads for option)
Printing width: 60cm
Printing Speed: 10~15sqm/h
Software: Maintop/Photoprint

Powder machine usually come with DTF printer, for printed film powder coating and curing.Then the film can be transferred on any kind of fabric materials.

Wi-Fi wireless printing, place it wherever you want, support Epson iPrint to realize a variety of printing applications, and easily share. Support Email Print: You can set an email address for the printer, send Email to the printer, and then print.

Product attribute introduction: UV ink printing transfer sticker, suitable for hard surface, plane, curved surface and other objects

Five Guarantees
1. Quality: no fading, strong stickiness
2. Factory: source manufacturers, innovation and worry-free
3. Team: one-to-one service, free design
4. Choice: a variety of crafts for you to choose
5. After-sale: quality problem, free re-send

A3 DTF Pro textile printer is widely used for different products, for example T-shirt, hats, shoes, bags. It requires a DTF printer, a shake powder machine and a heat press to get final products. Since it is cost effective, small size and environmentally friendly, customers who want to start new business are very interested in it.

No need to engrave waste and lamination, improve production efficiency, unlimited patterns, natural hollowing, lighter and breathable, short cycle and fast delivery, breaking through the limitations of traditional process color registration plate making, no plate making, 1 piece minimum order cost-effective, no high cost The investment in equipment and venues greatly reduces the investment cost.

There are 8 reasons for the failure of the uv flatbed printer, and there are 8 reasons for it. According to the difference in the design of uv flatbed printers of different manufacturers, there may be 10 reasons. There may be 6 different reasons. However, mastering the following 8 types can solve 99% of the failures of the nozzles not producing ink.

Using the shake powder could consider these procedures.
Dusting.
1.What is the powder sprinkled with?Hot melt powder, when the heat is sticky, after the formation of glue coating;
2.Why?Stick hot melt stick to the dry ink to help eventually form the coating;
3.How to sprinkle, sprinkle how fast?Can adjust the knob on the shake powder machine;
4.How much?The powder is about 2-3cm thick to stop sprinkling the powder.
Shaking.
1.Why shake powder?Shake off the excess powder on the ink and film adhesion, so that the powder is thin and evenly attached to the ink.
2.Shake powder speed.Depending on the situation, the knob on the condition machine, about 2-3 gear ok.
Drying.

1.Why drying?Melt the hot melt powder to create a reprint pattern coating;.
2.How long will it bake?Undefinite, depending on the specific situation, mainly to ensure that the pattern feels no powder, hot melt powder all melted into coating.
3.Temperature? 90-130 ° C is ok.

UV flatbed printers have pass trace, which is theoretically unavoidable, and mechanical errors cannot be eliminated to zero. But the higher the accuracy, the smaller the pass trace phenomenon and will not affect the printing quality. The cause of the pass trace of the pattern: the print feathering is too low, the two-way printing is too fast, the Y-axis belt is loose, the nozzle is in a bad state, and the ink is broken.

As professional DTF supplier,we can offer one stop service like hot melt powder shaking machine. This powder shaking machine is automatic dusting and curing the PET film while printing, can improve the production effciency. Meanwhile,we can offer together the hot melt powder and PET film.

The powder shaker is rotated at a high speed and the heat transfer material is hit, so that the powder on the material will be shaken more evenly and the excess powder on the material will not be adsorbed on the invalid picture.

Our DTF ink (aka Direct to Film ink) has been carefully selected and tested, and our DTF ink manufacturing partners carefully scrutinized to ensure the quality standards in ink production and consistency.for Black, Cyan, Magenta, Yellow and White; The DTF ink / transfers can be transferred to a variety of textiles and fabrics (cotton, polyester and more) as well as other substrates. Although all our DTF inks will work on a variety of engines, we also offer the desktopDTF and wideDTF ink series that are formulated for a more specific set of printheads / printer engines.

-Environmentally friendly and non-toxic
-Support customization, free design
-High-definition printing, quality assurance
-Azo free, oeko-tex standard
-Choose TODOjet product quality and after-sales guarantee

DTF-T30 A3 DTF Printer Features

Advanced Printheads: Equipped with 2 or 3 Epson I1600-A1 printheads for precise and high-speed printing.
Vivid Color Output: Dual CMYK + White ink configuration ensures vibrant, full-color prints with crisp, high-opacity white details for multi-material transfers.
Fast Printing Speed:
6 PASS: 12m²/h
8 PASS: 8m²/h
Ideal for both fast production runs and high-resolution detailed prints.

A new generation of intelligent white ink direct-injection transfer machine, which is cleaner to shake powder, eliminates static electricity, heats up and down, does not regain moisture when returning to the south, and adds suction to the front plate, and paper does not go astray. It has eight characteristics.

During the curing process, the hot melt powder may produce some gas, here we need the air purifier for cleaning. TODOjet can offer you one-stop solutions of DTF printing, such as the DTF printer, powder shaker machine,PET film, hot melt powder,pigment ink and so on.

When it comes to nozzles, the first thing everyone thinks of is the printer. The well-known printers are HP, Epson, Canon, Lenovo, Brother, Samsung and so on. These printers are now office type printers.

Heat transfer printing: For the embodiment of details, it is required that the white color of the printer be accurately aligned. Under normal printing speed of 6pas bidirectional printing, the printing accuracy should be high. We can print and heat transfer down to 0.3 mm at a speed of 24 meters per hour. of thin lines.

Wide color gamut and high color reproduction:Print what you want, and give you a more real experience with full colors High-speed printing without manual after-sales worry-free High-speed printing mass production

K-PRINT is one of the largest and most influential international exhibitions in Korea, with an exhibition scale of 25,000 square meters and more than 400 exhibitors. It is an exhibition with great development prospects selected by the Ministry of Industry, Trade and Resources of Korea. , is also a printing feast created by the official comprehensively integrating multiple resources.

Our latest DTF Printers (Direct to Film Printers) are revolutionizing textile printing with their ability to print on a wide range of fabrics, including cotton, silk, polyester, denim, and more. Thanks to advancements in DTF technology, this method is rapidly becoming one of the most popular choices in the printing industry, outpacing traditional printing techniques. Our AGP DTF Printers offer exceptional quality and reliability, backed by outstanding after-sales service. Choose TODOjet for your DTF printing needs and experience the future of textile printing today!

The main purpose of the UV print head cleaning liquid is to clean the internal channels of the print head to keep it open and smooth the ink discharge.

TYPE: UV INK
SUITABLE FOR: Printer with Epson DX7 DX5 XP600 TX800 head
COLOR: CMYK+LC+LM+White+Varnish
TESTING: 100% testing on the machine before shipment
HARD UV INK:
mainly printing on hard type materials, like Wood, Glass, Acrylic, Metal, Crystal, etc.
SOFT UV INK:
mainly printing on soft type materials, like leather, vinyl, TPU, EVA, wall paper, lamp box, etc.